MP series
- Measuring RMS
- Multi input range
- Wide display range
- 4rows (-1999~9999), 5rows (19999~99999)

High Accuracy, High Performance and Reliable Measurements
• 0.02% basic DC accuracy
• Large display with 50,000 counts
• Dual display for double indication for AC and DC, V and Hz, etc.
• True-RMS Measurements AC and AC+DC
• Wide AC Frequency bandwidth from 10Hz to 100kHz *
• True-RMS or MEAN value detection mode can be selected *
• Fast Peak Hold response time of 250µs
• Low-pass filter for motor drive measurements *
• Low Power Ω for resistance measurements on sensible electronic circuits by a low and safe test current *
• User calibration function
* Only for KEW 1062

1061/1062
CE
(Photo: 1062)
Safety design for industrial use
• Complies with IEC 61010-1 CAT.III 1000V, CAT.IV 600V
• Terminal shutter to prevent incorrect test leads' insertion in current terminals
• Very wide operating temperature range from -20 to 55ºC
Reliable support for data management
• Large data internal memory
KEW 1062: 10,000 data (logging), 100 data (manual)
KEW 1061: 1,000 data (logging), 100 data (manual)
• Download data and Live Monitoring on a PC via the USB interface
(Option for USB Communication set)

High Accuracy, High Performance and Reliable Measurements
• 0.02% basic DC accuracy
• Large display with 50,000 counts
• Dual display for double indication for AC and DC, V and Hz, etc.
• True-RMS Measurements AC and AC+DC
• Wide AC Frequency bandwidth from 10Hz to 100kHz *
• True-RMS or MEAN value detection mode can be selected *
• Fast Peak Hold response time of 250µs
• Low-pass filter for motor drive measurements *
• Low Power Ω for resistance measurements on sensible electronic circuits by a low and safe test current *
• User calibration function
* Only for KEW 1062

1061/1062
CE
(Photo: 1062)
Safety design for industrial use
• Complies with IEC 61010-1 CAT.III 1000V, CAT.IV 600V
• Terminal shutter to prevent incorrect test leads' insertion in current terminals
• Very wide operating temperature range from -20 to 55ºC
Reliable support for data management
• Large data internal memory
KEW 1062: 10,000 data (logging), 100 data (manual)
KEW 1061: 1,000 data (logging), 100 data (manual)
• Download data and Live Monitoring on a PC via the USB interface
(Option for USB Communication set)

High Accuracy, High Performance and Reliable Measurements
• 0.09% basic DC accuracy
• Large display with 6,000 counts
• True-RMS Measurements
• True-RMS or MEAN value detection mode can be selected *
• Low-pass filter for motor drive measurements
• User calibration function
Safety design for industrial use
• Complies with IEC 61010-1 CAT.IV 600V,
CAT.III 1000V
• Terminal shutter to prevent incorrect test leads' insertion in current terminals
• Very wide operating temperature range from
-10 to 55ºC

1051/1052
CE
(Photo: 1052)
Reliable support for data management *
• Large data internal memory *
KEW 1052: 1,600 data (logging), 100 data (manual)
• Download data and Live Monitoring on a PC via the USB interface
(Option for USB Communication set) *
* Only for KEW 1052

High Accuracy, High Performance and Reliable Measurements
• 0.09% basic DC accuracy
• Large display with 6,000 counts
• True-RMS Measurements
• True-RMS or MEAN value detection mode can be selected *
• Low-pass filter for motor drive measurements
• User calibration function
Safety design for industrial use
• Complies with IEC 61010-1 CAT.IV 600V,
CAT.III 1000V
• Terminal shutter to prevent incorrect test leads' insertion in current terminals
• Very wide operating temperature range from
-10 to 55ºC

1051/1052
CE
(Photo: 1052)
Reliable support for data management *
• Large data internal memory *
KEW 1052: 1,600 data (logging), 100 data (manual)
• Download data and Live Monitoring on a PC via the USB interface
(Option for USB Communication set) *
* Only for KEW 1052

• Digital Phase Indicator with open phase checker.
• Phase indicator designed to check the presence of open phase and also the phase sequence by LED and buzzer at the same time.
• Small, lightweight, and portable.

• Digital Phase Indicator with open phase checker.
• Phase indicator designed to check the presence of open phase and also the phase sequence by LED and buzzer at the same time.
• Small, lightweight, and portable.

Safe Testing without direct contact with live wires!!
• New technology permits safe testing, without the need of direct contact between probes and live wires.
• The insulated crocodile clips can clip insulated cables from φ2.4 to 30mm.
• Phase rotation is indicated by the rotary illumination of LEDs and logical audible tones.

• KEW8031F is designed to check phase sequence.
Lamps provided on the unit will also tell you if a phase is open.
• Can check a wide range of 3-phase power source from 100V to 600V.
Sealed against dust, the unit ensures trouble-free performance.
• Small, Lightweight and portable.
Designed for maximum ease of operation and ruggedness.
• No exposed metal parts, Safety features are incorporated including the instant push button switch operation.

• Waterproof hand-held Infrared Thermometer.
• Safe even if getting wet. Dustproof and waterproof structure of IP67.
• Possible to wash
• Please feel secure to use the product on the spot, made from ABS resin of antibacterial specification.
• Shock-proof structure: No damage even if dropped from the height of 1m.
• With auto-power-off function, preventing consumption of the battery
• Wide Temperature Range of -40ºC to 300ºC
• Small and light: Possible to measure easily by one hand.
• Portable type: Convenient to carry

• Simple temperature measurement from -40ºC to 500ºC
• Laser sight pinpoints measured spots.
• Palm size,lightweight 180g only.
• Automatic power off for saving battery life.
• Maximum or minimum temperature display.
• Audible buzzer high alarm standard.
• Emissivity adjustable from 0.30 to 1.90 in 0.01 steps.
• Backlight.

• Digital Light Meter
• 3 ranges changeable from low to high illuminance. (200/2000/20000lux)
• Data hold function.
• Digital light meter with separate light recieving sensor and meter.

• Digital Illuminometer
• Model 5201 is a highly portable and compact digital illuminometer for measuring illuminance from 0.1 to 19,990 Lux, with auto range switching.
• The digital display is held for a preset time (about 20 seconds) and, therefore, facilitates reading, recording and measuring in any direction.

• Can measure Flicker in accordance to IEC 61000-4-15 and EN50160 standards. Using our Flicker sensor, available as optional accessory, Pst value (short term severity in 10 minutes value) and the Plt value (long term severity in 2 hours value) can be measured.
• 12 kinds of Power Measurements for Power Control and Applicable to Power Quality Control including Harmonics Analysis.
• One click easy-to-use operation helps complicated setting and processing of large data through the setting / analyzing software provided as accessory.
• Direct communication with PC via USB cable
• Built-in Input / Output Function of external signal enables the signal transmission to alarms.
• 2-way power supply by AC and Battery, and Nickel hydrogen battery usable with rechargeable function.
• Pull / Insert of CF card possible whenever on recording under the function of memory backup device.
• Can monitor insulation at leakage current by using optional leak clamp sensors.
• Built-in Print Screen Function enables to record display screen (Records 512 screens by using CF card: 1 screen 40KB).
• Can display Waveform and Vector, and can confirm the wiring connection, too.
• Complies fully with International Safety Standards
IEC 61010-1 CAT.III 600V.

• 12 kinds of power measurements
• Regenerative electric power can be measured
• Display 3 different data simultaneously on large screen.
• 4 types wiring system
• Recording internal can be set between 1 second and 1 hour
• Demand measurement
• Double power supply system AC line and Alkaline size AA battery LR6 : 6 pcs.
• Supplied with interface software for downloading data to PC via USB
• Direct communication with PC by USB connection
• The interface for compact flash card (CF card) is equipped.
• Back light function
• Designed to Safety Standard IEC 61010-1 CAT.III 600V.

• Comprehensive real-time monitoring, recording and analysis of single and 3-phase systems
• Voltage, Current, Power Factor and Frequency measurements
• Power analysis (Active, Apparent and Reactive power)
• Energy analysis (Active, Apparent and Reactive power)
• Active power accuracy: ±0.3%rdg±0.2%f.s.
• Automatic wiring check function to prevent incorrect connections
• Large memory capability (2GB) using built-in SD card interface
• Real time & remote measurements using Android application
• synchronous measurements between two units of KEW 6305
• Wide selection of clamp sensors allow measurements from 0.1A to 3000A
• The instrument automatically recognizes what kind of clamp sensor is connected to it
• Windows software for data analysis and setting via USB port or Bluetooth

The Model 6202 is a hand-held portable appliance tester, performing four functions to ensure the Safety of ClassI, ClassII and ClassIII 230V appliances. And also can measure the mains voltage.
Readings are displayed on a large liquid crystal display (LCD) below which are eight LEDs which unambiguously display a pass or fail indication for threshold values dictated by DIN VDE 0701/0702

The KEW 6201A is a portable appliance tester, performing four functions to ensure the Safety of ClassI and ClassII appliances. And also can measure the mains voltage.
Readings are displayed on a large liquid crystal display (LCD) below which are four LEDs which unambiguously display a pass or fail indication for threshold values dictated by AS/NZS 3760.

6050 (LOOP+RCD)

Product Catalogue

Software

6050

• Kew Combitester provides the ultimate in Microprocessor technology offering Loop and RCD tests with a comprehensive memory and downloading test results.
• LOOP Impedance 200/2000Ω range measurement is carried out using a test current of 15mA. This current will not trip RCD’s rated at 30mA or greater.
• High resolution for low Loop Impedance (resolution of 0.01Ω) on 20Ω range.
• Direct reading of Prospective Short Circuit Current (PSC) and earth fault current.
• RCD tests at 0 and 180 degree phase angle switch permit quick tests and consistent readings.
• Test of a large kind of RCD's:
Standard, Selective, AC and A (DC sensitive breakers).
• Constant current source circuitry ensures that a fluctuating mains voltage does not affect the accuracy of readings.
• RCD Ramp test in order to indicate the actual tripping current of RCD.
• Contact Voltage Reading (UC). with two selectable contact voltage limits (50 and 25V).
• Visual indication of correct wiring status and automatic lock-out if test resistors overheats.
• Designed to IEC 61010-1, IEC 61557 and high protection degree IP54.
• The stored data can be transferred to PC via Optical Adapter Model 8212-RS232C and 8212-USB.

• Designed to meet IEC 61010-1 CAT.III 600V
• Test leads with remote control switch.
(For insulation&Simplified Earth Test)
• Back light function.
• Color coded scales and range switch position for easy reading.
• Automatic warning when resistance of auxiliary earth spikes is in excess of tolerance.
• Can be hung around the neck for both hand’s operation.

• Designed to meet IEC 61010-1 CAT.III 600V
• Test leads with remote control switch.
(For insulation&Simplified Earth Test)
• Back light function.
• Color coded scales and range switch position for easy reading.
• Automatic warning when resistance of auxiliary earth spikes is in excess of tolerance.
• Can be hung around the neck for both hand’s operation.

• Complies with IEC 61557
• Designed to IP 54 Rating
• Live circuit and wiring connection check LED's
• Triple ranges insulation tests at 250, 500 and 1000V
• Triple range loop and PSC tests 15mA test current at 200Ω/2000Ω range (No RCD Trip)
• Phase angle selection on RCD ranges
• Polarity switch for continuity tests
• Auto-null facility for continuity tests
• Earth probe for loop impedance testing on extraneous metalwork
• Contact Voltage Reading
• Test of a large kind of RCD's:
Standard, Selective, AC and A (DC sensitive breakers)

Continuity and Insulation Testing
• Live circuit warning LED:
Immediate illumination of a warning lamp if the circuit under test is live
• Auto Discharge:
Allows fast and safe discharge of electrical energy stored in capacitive circuits following testing
• Integral overload protection on internal continuity and insulation test circuitry
• Autoranging
• 500V DC test voltage for insulation tests
• 200mA short circuit current on continuity ranges

Loop and RCD Testing
• Wiring connection check LED's:
Immediate indication if wiring of circuit under test is correct
• Overheat Protection:
Rapid detection of overheating of internal circuitry,display of warning signal to user and automatic halting of measurement
• Supply Voltage Indication:
Can display supply voltage value in loop impedance mode
• Low Current Loop Impedance Test:
Short duration low test current will prevent tripping of many passive RCDs
• Auto Data Hold:
Retains displayed reading for set period following test
• Phase Angle Selection:
Selection of test current from +ve or -ve half cycle of waveform can prevent tripping of polarized type RCDs

• Continuity: 20/200Ω, 200mA Test Current
• Insulation: 500/1000V, 20/200MΩ, 1mA Rated Test Current
• Loop Impedance: 20/2000Ω, 15mA Test Current at 2000Ω (No RCD Trip)
• RCD: 10/30/100/300/500mA x1/2, x1, Fast Trip(40ms), DC, Auto Ramp
• Test of a large kind of RCD's:
Standard, Selective, AC and A (DC sensitive breakers)
• Uc (Contact Voltage): 100V
• Designed to IEC 61010-1, IEC 61557
• Data Memory: 300 measured results
• The stored data can be transferred to PC via Optical Adaptor Model 8212-USB or 8212-RS232C.

The KEW 6016 Multi-Function tester performs 10 functions
in one instrument.
• Continuity tester
• Insulation resistance tester
• Loop impedance tester
• PSC tester
• PFC tester
• RCD tester
• Earth tester
• Phase rotation tester
• Voltage measurement
• Frequency measurement

• Accurate digital readout of tripping time.
• Two neon lamps give quick check for correct wiring.
• Compact, lightweight and simple to operate.
• Zero cross circuitry permits testing at 0 and 180 degree portion of sine wave. At these two tests minimum (best) and maximum (worst) trip times will be displayed.

• Custom microprocessor controlled for highest accuracy and reliability.
• 3 LEDs for checking correct wiring status.
• 0 and 180 degree phase angle switch permits quick tests and consistent readings.
• Digital read-out of tripping time.
• Constant current source circuitry ensures that a fluctuating mains voltage does not affect the accuracy of readings.
• Large custom digital display readout.
• Visual indication of reversed phase and neutral wiring at socket.
• Designed to IP54 Rating.
• Complies with IEC 61557
• Test of a large kind of RCD's:
Standard, Selective, AC and A (DC sensitive breakers)

• Measurement of RCD trip time
• Measurement of trip out current
• Remote Test
• Voltage Measurement
• Auto-detection of Contact voltage
• Dust- and Water-proof
• Backlight

• Custom microprocessor controlled for highest accuracy and reliability.
• 3 LEDs for checking correct wiring status.
• 15mA LOOP measurement
• Direct reading of Prospective Short Circuit Current (PSC).
• Safe voltage measurement function.
• Large custom digital display readout on all models.
• Measure low loop resistances(resolution of 0.01Ω)
• Automatic lock-out if test resister overheats.
• Large custom digital display readout .
• Visual indication of reversed phase and neutral wiring at socket.
• Designed to IP54 Rating
• Complies with IEC 61557

Anti-Trip Technology "ATT"
No RCDs tripping during Loop Testing!

KEW 4300 is simplified earth resistance tester
(based on 2-pole method)
• 200/2000Ω (2 ranges): auto-ranging.
• Warning buzzer triggered at 100Ω or less.
• LED lights up when a large earth voltage is detected.
• Live circuit warning when 30V or higher voltage is detected.
(KEW 4300 detects voltage even when measuring resistances.)
• LED light for illuminating measurement points.
(It turns on/off automatically in relation to the ambient brightness.)
• Small test current (max 2mA) not triggering RCD.

• Dust and drip proof.(designed to IEC 529 IP54)
• In addition to the facility for precision measurement, test leads for simplified two wire measuring system also supplied as standard accessories.
(unit can be hung from the neck for simplified measurement)
• Designed to meet IEC 61010-1 safety standard.
• Capable of measuring earth voltage.
• Automatic warning when resistance of auxiliary earth spikes is in excess of tolerance.
• Small and lightweight. Shock resistant new case material.
• 2mA measuring current permits earth resistance tests without tripping earth leakage current breakers in the circuit under test.

• Dust and drip proof.(designed to IEC 529 IP54)
• In addition to the facility for precision measurement, test leads for simplified two wire measuring system also supplied as standard accessories.
(unit can be hung from the neck for simplified measurement)
• Designed to meet IEC 61010-1 safety standard.
• Capable of measuring earth voltage.
• Automatic warning when resistance of auxiliary earth spikes is in excess of tolerance.
• Small and lightweight. Shock resistant new case material.
• 2mA measuring current permits earth resistance tests without tripping earth leakage current breakers in the circuit under test.

• The latest circuit design permits the instrument to operate with the minimum of influence from earth voltage and earth resistance of auxiliary earth spikes.
• Dust and drip proof. (designed to IEC 529 IP54)
• Earth resistance value can be read directly from the scale.
• Designed to meet IEC 61010-1 safety standard.
• Capable of measuring earth voltage.
• Small and lightweight. Shock resistant new case material.
• 2mA measuring current permits earth resistance tests without tripping earth leakage current breakers in the circuit under test.
• Lead wire connection to C and P terminals and proper auxiliary earth resistance can be checked by "OK" lamp. Lead wire connection to C and E terminals is good when "OK" lamp is illuminated.

• The latest circuit design permits the instrument to operate with the minimum of influence from earth voltage and earth resistance of auxiliary earth spikes.
• Dust and drip proof. (designed to IEC 529 IP54)
• Earth resistance value can be read directly from the scale.
• Designed to meet IEC 61010-1 safety standard.
• Capable of measuring earth voltage.
• Small and lightweight. Shock resistant new case material.
• 2mA measuring current permits earth resistance tests without tripping earth leakage current breakers in the circuit under test.
• Lead wire connection to C and P terminals and proper auxiliary earth resistance can be checked by "OK" lamp. Lead wire connection to C and E terminals is good when "OK" lamp is illuminated.

Earth Resistance Measurements with 4, 3 and 2 Wires
Earth Resistivity (ρ) Measurement using WENNER method

• The earth resistance from 0.05 to 1200Ω can be measured without the auxiliary earth spikes. (The Multiple Earthing System.)
• True RMS
Accurate true RMS readings of AC current including distorted waveform from 1mA to 30.0A
• Noise Check Function
A function to detect current, which effects on an earth resistance measurement and display "NOISE" mark on the LCD.
• Memory function
Save and display up to 100 measurement data.
• Data hold function / Buzzer function / Back light function
• Compliant with Safety Standards of IEC 61010-1 : CAT.IV 300V Pollution degree2

Various useful functions are available on Android devices using Bluetooth communication
• Real time measurements can be transferred, shown and saved on Android device (up to 100 measurements)
• Saved data includes measurement, GPS location and date & time
Easy to check on map "When" and "Where" the measurement was made
• Comparator function on Android device informs when the measured value is lower/higher than the preset value
Earth /Ground resistance and Leakage current measurement functions
• The earth resistance from 0.05 to 1200 Ω can be measured without the auxiliary earth spikes in multi-earthing systems
• True RMS leakage or phase current readings from 0.1mA to 30.0A provides vital additional information in earthing networks
• Filter function offers increased immunity to electrical noise and a Noise mark appears in excessively high noisy environments

• Compact and lightweight digital Insulation / Continuity tester.

• Bargraph to display insulation resistance.
• Displays the value of external AC voltage along with flashing symbol.
• Auto null function to automatically subtract the test lead resistance before displaying the real continuity resistance value.
• Live circuit warning beeper.
• Releasing the test button automatically discharges the charges stored in the circuit under test.
• 200mA continuity measuring current to IEC 61557.
• Minimum 1mA current on insulation tests to IEC 61557.

• Bargraph to display insulation resistance.
• Displays the value of external AC voltage along with flashing symbol.
• Auto null function to automatically subtract the test lead resistance before displaying the real continuity resistance value.
• Trac-Lok mode to conserve battery life on insulation and continuity tests.
• Live circuit warning beeper.
• Releasing the test button automatically discharges the charges stored in the circuit under test.
• Backlight function to view the test results in dimly lit areas.
• 200mA continuity measuring current to IEC 61557.
• Minimum 1mA current on insulation tests to IEC 61557.

3 functions in one unit, insulation test with 4 voltage ranges, continuity test, AC voltage measurement
• 200mA measuring current on continuity testing
• Comparator function with PASS / FAIL and buzzer
• 0Ω adjustment at continuity measuring range
• Memory function up to 99 data
• Backlight LCD provides easy reading in dark locations
• Safety lock system prevents an erroneous operation on 500 and 1000 Volt ranges
• Safety standard IEC 61010-01 CAT.III 600V

3 functions in one unit, insulation test with 4 voltage ranges, continuity test, AC voltage measurement
• 200mA measuring current on continuity testing
• Comparator function with PASS / FAIL and buzzer
• 0Ω adjustment at continuity measuring range
• Memory function up to 99 data
• Backlight LCD provides easy reading in dark locations
• Safety lock system prevents an erroneous operation on 500 and 1000 Volt ranges
• Safety standard IEC 61010-01 CAT.III 600V

3 functions in one unit, insulation test with 4 voltage ranges, continuity test, AC voltage measurement
• 200mA measuring current on continuity testing
• Comparator function with PASS / FAIL and buzzer
• 0Ω adjustment at continuity measuring range
• Memory function up to 99 data
• Backlight LCD provides easy reading in dark locations
• Safety lock system prevents an erroneous operation on 500 and 1000 Volt ranges
• Safety standard IEC 61010-01 CAT.III 600V

• Dust and drip proof construction. (designed to IEC 60529 IP54)
• Designed to meet IEC 61010-1 and IEC 61557 safety standard.
• 1mA rated test current at the minimum resistance.
• 200mA measuring current on continuity testing.
• Automatic discharge of circuit capacitance.
(Any charge stored in the circuit under test will be automatically discharged after testing.)
• Live circuit warning buzzer and neon lamp.
• Small and lightweight. Shock resistant new case material.
• AC voltmeter with linear, easy-to-read scale.
• Operates on AA, R6P×6 dry batteries.

• Test insulation up to 100MΩ at 250V, 200MΩ at 500V, 400MΩ at 1000V and continuity up to 20Ω.
• LIVE circuit warning lamp plus audible warning.
• Automatic discharge of circuit capacitance when TEST button is released.
• Fuse protected (continuity range only).
• Battery check LED.
• Front panel zero adjust.
• Back light function to facilitate working at dimly lit situations.
• PRESS TO TEST button with lock down feature.

• 500V/1000MΩ (Model 3165)
• 1000V/2000MΩ (Model 3166)
• Expanded megohm scale for easy reading.
• New robust housing case to prevent damage.
• AC voltmeter scale for easy reading.
• Neck strap for both hand’s operation.

• 500V/1000MΩ (Model 3165)
• 1000V/2000MΩ (Model 3166)
• Expanded megohm scale for easy reading.
• New robust housing case to prevent damage.
• AC voltmeter scale for easy reading.
• Neck strap for both hand’s operation.

• Miniature lightweight insulation tester. It weighs only 340g(battery included), but carries full measurement functions.
• Automatic discharge of circuit capacitance.
• Test leads with remote control switch.
• New robust housing case.
• Back light function.
• Neck strap for both hand?s operation.

• Miniature lightweight insulation tester. It weighs only 340g(battery included), but carries full measurement functions.
• Automatic discharge of circuit capacitance.
• Test leads with remote control switch.
• New robust housing case.
• Back light function.
• Neck strap for both hand?s operation.

• Miniature lightweight insulation tester. It weighs only 340g(battery included), but carries full measurement functions.
• Automatic discharge of circuit capacitance.
• Test leads with remote control switch.
• New robust housing case.
• Back light function.
• Neck strap for both hand?s operation.

• Miniature lightweight insulation tester. It weighs only 340g(battery included), but carries full measurement functions.
• Automatic discharge of circuit capacitance.
• Test leads with remote control switch.
• New robust housing case.
• Back light function.
• Neck strap for both hand?s operation.

• AC Voltmeter with linear, easy-to-read scales.
• Auto discharge function; any charge stored in the circuit under test will be automatically discharged after testing.
• Designed to meet IEC/EN 61010-1 CAT.III 600V, CAT.II 1000V
• Color-coded scales for easy reading.
• Back light function to facilitate working at dimly illuminated locations.
• Test lead set with remote control switch.
• Shoulder strap for hands free.

• AC Voltmeter with linear, easy-to-read scales.
• Auto discharge function; any charge stored in the circuit under test will be automatically discharged after testing.
• Designed to meet IEC/EN 61010-1 CAT.III 600V, CAT.II 1000V
• Color-coded scales for easy reading.
• Back light function to facilitate working at dimly illuminated locations.
• Test lead set with remote control switch.
• Shoulder strap for hands free.

• AC Voltmeter with linear, easy-to-read scales.
• Auto discharge function; any charge stored in the circuit under test will be automatically discharged after testing.
• Designed to meet IEC/EN 61010-1 CAT.III 600V, CAT.II 1000V
• Color-coded scales for easy reading.
• Back light function to facilitate working at dimly illuminated locations.
• Test lead set with remote control switch.
• Shoulder strap for hands free.

• 4 test voltages plus AC voltage range.
• Colour coded scales and range switch position for easy reading.
• Test leads with remote control switch.
• New robust housing case.
• Back light function.
• Neck strap for both hand's operation.

• 4 test voltages plus AC voltage range.
• Colour coded scales and range switch position for easy reading.
• Test leads with remote control switch.
• New robust housing case.
• Back light function.
• Neck strap for both hand's operation.

• Permits a wide range of insulation testing up to 100GΩ at variable test voltage from 1kV to 10kV.
• DC voltage output for recorders.
• Output voltage is shown on the digital display.
• After tests, automatically discharges the charges stored in the circuit under test.
• Operated by rechargeable Nickel-Cadmium batteries.

• Wide range measurements from 500V to 5000V and up to 1000GΩ .
• Large digital display with Bar Graph indication and back light.
• Polarization Index measurement (PI).
• Timer measurement function.
• Indication of Output voltage and Discharge voltage.
• Auto-discharge function and Voltage output warning function.
• Auto power off and Battery Check.
• Safety standard IEC 61010-1 CAT.III 600V

Test voltage up to 5kV, Resistance up to 1TΩ
Short-Circuit Current up to 5mA

Test Voltage up to 12kV, Resistance up to 35TΩ,
Short-Circuit Current up to 5mA.
Graphic representation on large backlight display

Rugged Design for Field Use

Rugged Design for Field Use

Rugged Design for Field Use

3 channel inputs for the simultaneous recording of Leakage Current, Load Current and Voltage
• Power Quality analysis (only on KEW 5020)
• Large capacity for storing 60,000 data points
• Lowpass Filter will filter out the harmonics
• LED flickers when the preset current/voltage value is exceeded
• CALL:Confirmation of recorded data
• Selection of One-time mode or Endless mode
• Non Volatile Memory
• Battery power indicator
• The userfriendly PC software "KEW LOG Soft 2" is supplied
• Continuous measuring time:Approx. 10 days (Alkaline Battery)

3 channel inputs for the simultaneous recording of Leakage Current, Load Current and Voltage
• Power Quality analysis (only on KEW 5020)
• Large capacity for storing 60,000 data points
• Lowpass Filter will filter out the harmonics
• LED flickers when the preset current/voltage value is exceeded
• CALL:Confirmation of recorded data
• Selection of One-time mode or Endless mode
• Non Volatile Memory
• Battery power indicator
• The userfriendly PC software "KEW LOG Soft 2" is supplied
• Continuous measuring time:Approx. 10 days (Alkaline Battery)

THE LEAKAGE CURRENT IS RECORDED BY 3CH INPUT
60,000 DATA IS RECORDED
60,000 data is recorded when 1ch is used and when three all channels are used, 20,000 data is recorded for each channel
• Continuous measurement time
• Data where it doesn’t disappear even if battery is consumed
• Battery residual display
• The present time, recording intervals, the start of recording, the recording method, the name of monitoring site and the comment can be set by using supplied software
• Selection of one time mode and endless mode
• Recall function

• Least affected by external stray magnetic field.
• 20mA AC max. in proximity to a 15mm-dia conductor carrying 100A AC
• Frequency Selector Switch to eliminate the effect of harmonics.

• Frequency Selector Switch to eliminate the effect of harmonics.
• Three AC current ranges:40mA/400mA/400A.

• Frequency Selector Switch to eliminate the effect of harmonics.
• Three AC current ranges:40mA/400mA/400A.

• High Sensitive Model
• Frequency Selector Switch to eliminate the effect of harmonics.
• Three AC current ranges:4mA/40mA/100A

• Frequency Selector Switch to eliminate the effect of harmonics.
• Three AC current ranges 20mA/200mA/200A.
• Rotary switch for easy one finger power-on and range selection.

• Large transformer jaws of 68mm diameter makes it possible to clamp on all three or four wires (3 phases) together for leakage current measurement.
• True RMS enables an accurate measurement for distorted waveforms.
• Measurement from mA up to AC 1000A
• Frequency filter switch to eliminate the effect of the harmonics.

• Extra wide transformer jaws are best suited for clamping on all three or four wires (3phases) together for leakage current measurement.
• Frequency filter switch to eliminate the effect of harmonics.
• Output terminal.

• Digital clamp meter with tear drop shaped, medium size transformer jaws specially designed for leakage current measurement.
• Frequency filter switch to eliminate the effect of harmonics.
• Output terminal for connection to recorders and facility to operate from external power supply permit continuous leakage current monitoring.

• True RMS reading is an essential feature for accurate measurement.
• “Non Contact” voltage function indicates the presence of AC voltage by warning the user with an audible signal.
• Set the DC current range to zero in one touch with the Zero Adjust function.

• Designed to meet international safety standard IEC 61010-1 CAT.IV 600V.
• CAT.IV Clamp Meters can measure the Voltage and Current in both every low and high power circuits.
• Thus, very useful for power distribution companies, power utilities and maintenance fields.
• True RMS enables an accurate measurement.

• Designed to meet international safety standard IEC 61010-1 CAT.IV 600V.
• CAT.IV Clamp Meters can measure the Voltage and Current in both every low and high power circuits.
• Thus, very useful for power distribution companies, power utilities and maintenance fields.

• Designed to meet international safety standard IEC 61010-1 CAT.IV 600V.
• CAT.IV Clamp Meters can measure the Voltage and Current in both every low and high power circuits.
• Thus, very useful for power distribution companies, power utilities and maintenance fields.
• True RMS enables an accurate measurement.

• Smallest clamp meter capable of AC and DC current measurements.
• 300A auto ranging has minimum resolution of 0.01A AC/DC.
• Auto-zero function to allow one touch zero adjustment.

• High sensitivity, miniature AC/DC clamp meter.
• 0.1mA minimum resolution for AC current and 1mA minimum resolution for DC current.
• Output terminal for recorder connection.

• CAT.IV Clamp Meter can measure the Voltage and Current in both very low and high power circuits.
• Accurate True-RMS reading of AC current or voltage with distorted waveform.
• Can measure AC and DC currents up to 2000A.
• Output terminal for connection to recorders.

• Smallest clamp meter capable of AC and DC current measurements.
• 20A range has a minimum resolution of 0.01A AC/DC.
• AC/DC voltage and resistance measurement functions also available.

• Equipped to measure both AC and DC current with transformer jaws of large diameter.
• Can measure AC and DC currents up to 2000A.
• Output terminal for connection to recorders.

• Range switch selects only one rotary scale at a time, making it easy to take readings correctly.
• A long time seller with proven reputation world wide for its easy-to-use functions.

• DC voltage range is also available especially for checking emergency battery operated power supply.
• Can measure temperature using optional probe.
• Tear drop shaped transformer jaws for ease of use.

The Slim and Lightweight 1000A AC Clamp Meter

• Designed to meet international safety standard IEC 61010-1 CAT.IV 600V.
• CAT.IV Clamp Meters can measure the Voltage and Current in both every low and high power circuits.
• Thus, very useful for power distribution companies, power utilities and maintenance fields.

• Can measure large AC current up to 200A.
• 24mm-dia tear drop shaped jaws.

• True RMS reading instrument that permits precise measurements of nonsinusoidal waveform AC current and voltage. Accurate measurements are also possible at low frequencies from 10Hz upwards.
• Designed to meet internationally proven safety standards such as
IEC 61010-1, UL3111 and VDE0411.
• Three functions in one unit; AC current, AC voltage and resistance.

• Tear drop shaped jaws for ease of use in tight places and crowded cable areas.
• Designed to meet internationally proven safety standards such as
IEC 61010-1, UL3111 and VDE0411.
• Three functions in one unit; AC current, AC voltage and resistance.
• Resistance range provides audible continuity test.
• Frequency response from 40Hz to 1kHz on AC current and voltage ranges.

• Sleep function to save battery
• Data hold function.
• Digital display with maximum 4000 counts.

• Pocket size, handy clamp meter.
• UL listed fire retardant plastic housing case.
• Multifunction instrument having voltage and resistance measurement functions in addition to all the ranges incorporated.

• Can measure large AC current up to 2000A.
• Peak hold function.
• 55mm-dia large tear drop shaped jaws.

• Can measure large AC current up to 2000A.
• Peak hold function.
• 55mm-dia large tear drop shaped jaws.

• 0.01mA resolution for DC current
• Top class measurement 0.2% accuracy
• Φ6mm clamp jaw easy to use in tight places
• Measurement from 0.01mA to 120.0mA
• Dual display with backlight shows both mA measurement and percent of 4-20 mA span
• Spotlight for illuminating measurement point
• Analog output terminal for recorder connection
• Complies with IEC 61010-1 CAT.II 300V

• Designed to meet international safety standards
IEC 61243-3/IEC 61010-1
Measurement Category (CAT.) IV 600V
• Self-Diagnostic test
• AC and DC voltage tests up to 690V with LED
• Polarity indication
• Single-pole phase test
• Phase rotation test
• Double molding gives comfortable grip
• Continuity test
• Auto-power ON/OFF
• Pen light for illuminating measurement points
• Variable distance in socket, 16.7mm or 19.0mm
• Variable probe Tips, 1.6mm or 4mmφ
• Probe cover protects user and probe Tips
• IP65 (IEC 60529)

• Designed to meet international safety standards IEC 61243-3/
IEC 61010-1 Measurement Category (CAT.) IV 600V
• Self-Diagnostic test
• AC and DC voltage tests up to 690V with LEDs and LCD
• Polarity indication
• Single-pole phase test
• Phase rotation test
• Double molding gives comfortable grip
• Continuity test
• Auto-power ON/OFF
• Pen light for illuminating measurement points
• Variable distance in socket, 16.7mm or 19.0mm
• Variable probe Tips, 1.6mm or 4mmφ
• Probe cover protects user and probe Tips
• IP65 (IEC 60529)

• High sensitivity DC20kΩ/V.
• 1m drop-proof heavy duty designed taut-band movement.
• Can measure line voltage up to AC 600V.
(Voltage to ground MAX AC300V) (Protected by 600V ceramic fuse against accidental overload)
• Continuity buzzer, battery check, LED check, temperature measurement function.
• Skeleton type robust and clear case with carrying handle furnished as standard accessory.